Exactly How To Install A Tub (For Beginners).
Exactly How To Install A Tub (For Beginners).
Blog Article
Each person will have their private thinking involving Installing A Bathtub.
Mounting a bath tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the task can relocate speedily; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make sure you have certified on your own for the task and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should make up the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to stop strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, put the tub in the needed position. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the tub till the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Load the bathtub and additionally examine the overflow electrical outlet and also the regular outlet for leaks.
Finally, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has actually been made use of at least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet and the sink. Secure the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former type must be attached to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is recommended to fit the tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to read through our article. Sharing is nice. Helping others is fun. Thanks for your time. Kindly visit our website back soon.
View Report this page